...

 ...

SHJD’s range of automatic sprinklers is compact, highly durable and comes in several temperature ratings and K-Factors to meet various design requirements. They are available in Pendants (SSP), Uprights (SSU), Sidewalls (HSW) and Conventional (C U/P). Incorporated with either 3mm (Quick Response) or 5mm (Standard Response) diameter frangible glass bulb. SHJD’s UL listed sprinkler heads are designed for use in light, ordinary, and extra hazard, commercial occupancies such as banks, hotels, shopping malls, factories, refineries, chemical plants, etc. If aesthetics is the major consideration, then Concealed Glass Bulb Flush Pendent Sprinkler (ZSTDY) should be your ideal choice. ADVANTAGES • UL Listed glass bulb and seal plate • Heat sensing component (glass bulb) and seal gasket from German • Small frame and narrow profile bulb for enhanced appearance • Chrome-plated finish for corrosive resistance • Assembled and tested in production line utilizing German equipment and methodology Specifications Accessory...

Context Plus ‘Standard’ Fire Performance Cable has been independently tested and approved by the LPCB to meet BS 5839- 1:2002+A2:2008 Clause 26.2d Standard, BS EN 50200:2006+Annex E 30 minutes, and BS EN 50200:2006 PH120 – under fire conditions. Materials and processes are recorded and tracked throughout manufacture to ensure consistent reliability and quality. Cable cores are twisted during manufacture to provide the highest level of data protection, ideal for long cable runs and analogue addressable fire systems. ADVANTAGES • Manufactured in the United Kingdom with a ten year warranty. • Low Smoke Zero Halogen emissions under fire conditions. • Easy to install and superb working flexibility. • Reduced installation time and costs. • All in one – easy to strip outer sheath. • No separate foil or additional fibre wraps. • No mica tape on conductors. • No additional core separators to remove. • Available in a variety of multi-core combinations all with CPC (circuit protection conductor). • 100m, 200m and 500m reels (other special lengths available to order). • Approved to meet a 3 hours only fire duration at 950°C & 2 hours fire and mechanical shock duration at 830°C. • Retains continuity for 30 mins under fire conditions at 830°C including 15 mins under fire & water conditions and with a mechanical shock applied every 5 minutes during the full 30 minute test....

An attractively-designed wall sounder offering low current consumption, high sound output, 7 volume levels and 15 selectable tone...

The Context Plus XP95 Manual Call Point is intended for indoor applications and incorporates a short circuit isolator which will ensure its operation in the event of a short circuit fault on the loop. The Call Point is surface mountable and has an easily resettable element rather than a break glass. It also features a unique ‘Plug and Play’ installation concept designed specifically to reduce installation time. The call point utilises a terminal block, where all installation cabling is terminated. Its address is set at the commissioning stage by means of a seven-segment DIL switch. A single bi-coloured alarm LED is provided which is controlled independently of the call point by the control panel. The LED is illuminated red when the call point has been activated and amber/yellow to indicate a short circuit. Once activated, the Call Point can be reset by inserting the test key into the bottom of the unit until the key clicks into position, next remove the test key and push the front cover up until it clicks home. Electrical Considerations The unit operates at 17-28V DC with protocol voltage pulses of 5-9V. No electrical supply greater than 50V AC rms or 75V DC should be connected to any terminal. Designed for indoor use only it includes four LEDs, two red and two yellow, which are visible through the front cover of the enclosure. One red LED is illuminated to indicate that the relay is set. The second red LED is illuminated to indicate that the switch input is closed. One yellow LED is illuminated whenever a fault condition (open or short circuit) has been detected. The other LED is illuminated whenever the built-in isolator has sensed a short-circuit loop fault. The enclosure is moulded from white self-extinguishing polycarbonate....